A furnace sits idle from spring to fall, then gets asked for heat on the first cold night. That is when a weak igniter, a clogged filter or a failing capacitor shows itself. A fall maintenance visit finds those parts first. FixitBay LLC services central gas furnaces, electric furnaces and heat pumps, and gas wall and floor furnaces across San Francisco, the Peninsula and Marin.
The visit starts with a $100 diagnostic, credited toward the work you approve. There is no published price for the visit: the technician looks at the furnace and writes an estimate, and nothing is replaced until you approve it. Parts we fit carry a 180-day warranty on parts and labor. Duct cleaning is not part of the visit, and we do not install furnaces.
Change the filter every 1 to 3 months while the heat is in use. Keep supply and return vents open and clear. Keep the space around the furnace free of boxes and paint. Test every carbon monoxide alarm once a month. Before the season, run the heat for 15 minutes: a burning-dust smell on the first run is normal, and no heat, a loud bang or a furnace that shuts off is not.
If the furnace has already stopped heating, see furnace repair. Call (760) 543-5733 or book a furnace maintenance visit.
FixitBay LLC services home furnaces in San Francisco, on the Peninsula and in Marin: central gas furnaces, electric furnaces and heat pumps, and gas wall and floor furnaces. A maintenance visit is a check of the parts that fail once the cold months start: the igniter or the pilot, the flame sensor, the safety switches, the blower, the gas connection at the furnace and the thermostat. The visit starts with a $100 diagnostic, and the technician writes an estimate for any part worth replacing before touching it. The $100 is credited toward the work you approve, and replaced parts carry a 180-day warranty on parts and labor. Book online and pick a 2-hour window, any day from 8 AM to 6 PM. We service and repair furnaces, and we do not install them.
We publish no fixed price for a furnace maintenance visit. The technician looks at the furnace on site and gives you an exact quote for the servicing, and the $100 diagnostic is credited toward the work you approve. What moves the number is the type of furnace (central, wall or floor, gas or electric), how easy it is to reach, and what the checks turn up. A part that is worth replacing goes on the written estimate with its price first, and you decide then. Parts we fit carry a 180-day warranty on parts and labor.
Once a year is the usual schedule, and most furnace makers ask for an annual check in their manuals. In San Francisco and along the coast the heating season is long and mild, so a furnace runs many short cycles through much of the year, and every start is one more ignition for the igniter and the flame sensor to handle. A furnace in a garage or a crawl space also collects dust on its burners faster than one in a hallway closet. Between visits, change the filter every 1 to 3 months while the heat is in use.
Early fall, before the first cold week. A furnace that sat idle since spring shows a weak igniter, a dirty flame sensor or a stiff blower on its first runs, and it is easier to find that in September or October than on a cold night in December. If the season has already started, a visit is still worth it: the checks are the same at any time of year.
We run the furnace through a heating cycle and work the same list on every unit. Ignition: the igniter or the pilot assembly, the flame sensor and the burner flame. Safety: the limit switch, the pressure switch, the rollout switches and the door switch. Air: the filter, the blower motor and its capacitor, and the inducer motor. Gas: the gas valve and a leak check at the connection to the furnace. Controls: the fault codes stored on the control board, the wiring and the thermostat. On a high-efficiency furnace we also check the condensate drain, and on a wall or floor furnace the thermocouple or the thermopile. You get a written note of what we found and which parts are near the end of their life. Duct cleaning is not part of the visit and is not a service we offer.
Yes. Tune-up, furnace service, annual inspection and furnace maintenance are four names for the same visit: a technician runs the furnace, tests the parts that wear, and replaces the ones that are failing before they stop the heat. What differs between companies is the list of checks. Ours is on this page, and anything beyond the checks goes on a written estimate first.
Watch for a furnace that takes several tries to light, starts and stops every few minutes, heats some rooms slowly, makes a new rattle, squeal or bang at start-up, shows a yellow or wavering burner flame where it used to be steady and blue, or burns more gas for the same weather. Most of these trace back to a clogged filter, a weak igniter, a flame sensor that has stopped reading the flame, or a blower that is wearing out. If the furnace has already stopped heating, book a repair visit instead: the diagnostic is the same $100 and it is credited toward the repair.
Sometimes, and the technician tells you before doing anything. Anything worth replacing goes on a written estimate at the visit, with the price and, if a part has to be ordered, the lead time, and you approve it first. A repair that needs an ordered part is scheduled as a return visit, and that visit carries no second diagnostic fee. Whatever we fit is covered by the 180-day warranty on parts and labor.
Change the filter every 1 to 3 months while the heat is in use, and write the date on its frame. Keep supply and return vents open and clear of furniture and rugs. Keep the space around the furnace free of boxes, paint and anything that burns. Test every carbon monoxide alarm once a month and replace each one at the age printed on its label. Change the thermostat batteries once a year. Leave the burners, the gas valve and the pilot adjustment to a technician.
We accept all major credit and debit cards (Visa, Mastercard, American Express, Discover), Apple Pay, Venmo, Zelle, online payment via secure invoice link, personal checks, and cash. You pay after the work is complete and you have approved it. We credit the $100 diagnostic visit fee toward the work if you proceed. If the repair needs a part ordered, we may ask for a deposit on that part before we order it. No processing fees, no hidden charges: the price you approve is the price you pay.