Furnace Repair in San Francisco & Bay Area

FixitBay LLC repairs home furnaces across San Francisco, the Peninsula and Marin County: central gas furnaces, electric furnaces and heat pumps, and the gas wall furnaces and floor furnaces that heat many older San Francisco houses and apartments. The common calls are a furnace that will not turn on, blows cold air, short cycles, leaks water, or has a pilot that will not stay lit.

$100 diagnostic, credited toward the repair. Written estimate before any work, usually the same day. 180-day warranty on parts and labor. A visit is usually open the same day or the next, any day from 8 AM to 6 PM. We repair and maintain furnaces and do not install new ones. For a check before the heating season, see furnace maintenance.

Call (760) 543-5733 or book online.

Service Areas for Furnace Repair

We provide furnace repair across San Francisco, the Peninsula, and Marin County. Select your city for local details and availability.

San Francisco Daly City South San Francisco San Bruno Pacifica Millbrae Colma Brisbane Montara San Rafael Novato Mill Valley

View all service cities

Common Furnace Problems

Furnace Not Turning On

No click, no fan, no heat. The thermostat, a tripped breaker, the door switch, the igniter or the control board.

Furnace Not Igniting

The inducer starts and the igniter glows or clicks, but the burners never light, or they light and drop out. Igniter, flame sensor, gas valve or pressure switch.

Blowing Cold Air

The fan runs and the air is cool. The furnace overheats on a clogged filter, the flame sensor shuts the burners off, or the pilot has gone out.

Pilot Light Will Not Stay Lit

On a wall or floor furnace the pilot lights and dies when you release the button. Thermocouple, thermopile, pilot assembly or gas valve.

Short Cycling

The furnace runs a minute or two, stops and starts again. Overheating, a weak flame signal or a thermostat fault.

Blower Will Not Stop or Start

The fan runs all day or never comes on. Fan setting, a stuck relay, the blower motor or its capacitor.

Loud Noises

A bang at ignition, a squeal, a rattle or a steady hum. Delayed ignition, blower bearings, a loose panel or a transformer.

Leaking Water

Water around a high-efficiency furnace. A clogged condensate drain or trap, a failed pump or a cracked hose.

Error Code or Flashing Light

The control board flashes a fault code behind the sight glass. We read the code and confirm it with a test before replacing anything.

Heat Pump Not Heating

The outdoor unit will not start, runs without heating or stays in defrost. Capacitor, contactor, sensors or the defrost control.

Furnace Repair vs. Replacement: How to Decide

The cases below show when a furnace repair makes sense and when a new furnace does.

  • Furnace under 15 years old with one failed part (Repair): Igniters, flame sensors, pressure switches, capacitors and motors are parts that wear. Replacing one puts the furnace back in normal service.
  • Wall or floor furnace with a pilot that will not stay lit (Repair): Usually a thermocouple, a thermopile or the pilot assembly. The cabinet and the burner of these furnaces outlast the small parts by many years.
  • Cracked heat exchanger (Replace): A cracked heat exchanger can let combustion gases into the air the furnace heats. It is a safety problem, and the furnace should be replaced by an installer.
  • Furnace over 20 years old with repeated breakdowns (Replace): When one expensive part follows another, the repair money is better spent on a new furnace. We tell you when you reach that point, and we do not install furnaces ourselves.

How We Diagnose and Fix Furnaces

1. We run the furnace and test what fails

We run a full heating cycle and read the fault code on the control board. Then we test the igniter or the pilot, the flame sensor, the pressure and limit switches, the inducer and blower motors, the gas valve and the thermostat circuit.

2. Written quote before any work

You get the estimate in writing after the diagnostic, usually the same day. If the part is on hand, we fix the furnace on the same visit once you approve. If it has to be ordered, the estimate gives you the price and the lead time first.

3. Fix, verify, back it for 180 days

After the repair we run the furnace through complete heating cycles, watch the ignition and the flame, and check the gas connections we opened for leaks. We back the repair for 180 days.

Frequently Asked Questions

Who repairs furnaces in San Francisco?

FixitBay LLC repairs home furnaces in San Francisco, on the Peninsula and in Marin: central gas furnaces, electric furnaces and heat pumps, and the wall furnaces and floor furnaces that heat many older San Francisco houses and apartments. The visit starts with a $100 diagnostic. The technician finds the failed part and writes an estimate, usually the same day, and the $100 comes off the total once you approve it. Every repair carries a 180-day warranty on parts and labor. We repair and maintain furnaces and we do not install or replace them, so nobody here earns anything by telling you to buy a new one. Book online and pick a 2-hour window, any day from 8 AM to 6 PM. A visit is usually open the same day or the next.

How much does furnace repair cost in San Francisco?

Every furnace repair starts with a $100 diagnostic. The technician runs the furnace through a heating cycle, tests the parts the symptoms point at, and writes an estimate, usually the same day. If you approve it, the $100 comes off the total. We publish no starting price for furnace repair, because the spread between a flame sensor and a blower motor or a control board is too wide to put in one number. What moves the price is the failed part, the type of furnace (central, wall or floor, gas or electric) and how hard the unit is to reach in a closet, a garage or a crawl space. You see the full price in writing before any work starts, and the repair carries a 180-day warranty on parts and labor.

Why is my furnace not turning on?

Start with four checks you can do yourself. Set the thermostat to Heat and a few degrees above room temperature, and replace its batteries if the screen is dim. Look at the breaker panel and at the switch on or beside the furnace, which looks like a light switch and gets turned off by accident. Check the filter: a clogged one overheats the furnace until a safety switch shuts it down. Make sure the furnace door panel is seated, because a door switch cuts the power when the panel is loose. If the furnace still stays off, the usual causes are a failed igniter, a flame sensor that no longer detects the flame, a pressure switch or inducer motor fault, or the control board. Those need a meter and a test cycle, which is what the $100 diagnostic covers.

Why is my furnace blowing cold air?

First look at the fan setting on the thermostat. On ON the blower runs all the time, including between heating cycles, so the air feels cool. AUTO runs it only while the burners are lit. If the setting is right, the furnace is probably lighting and then shutting its burners off. A clogged filter makes the furnace overheat, and a limit switch cuts the flame while the blower keeps running. A flame sensor that cannot detect the flame closes the gas valve a few seconds after ignition. On a wall or floor furnace, a pilot that has gone out or a weak thermocouple does the same. A heat pump blows cool air for a few minutes while it defrosts the outdoor coil, which is normal. Change the filter, and if the air stays cold, book the diagnostic.

Do you repair wall furnaces and floor furnaces?

Yes. Many San Francisco houses and apartments built before central heating became standard are heated by a gas wall furnace or a floor furnace, and we repair both. Most of these units run on a standing pilot and a millivolt circuit: the pilot heats a thermocouple or a thermopile, and that small voltage holds the gas valve open and answers the wall thermostat. The usual faults are a pilot that will not stay lit, a weak thermocouple or thermopile, a gas valve that no longer opens, a thermostat or its wiring, and on fan models a blower that has stopped. Williams, Empire and Cozy are the makes found most often. The visit is the same as for a central furnace: a $100 diagnostic credited toward the repair, a written estimate, and a 180-day warranty on parts and labor.

Which furnace brands do you repair?

We repair furnaces whatever the badge says. Most central furnaces in Bay Area homes are Carrier, Bryant, Lennox, Trane, American Standard, Rheem, Goodman or York, and most wall and floor furnaces are Williams, Empire or Cozy. The ignition, flame sensing, blower and safety circuits follow the same patterns across makers, so the diagnostic is the same. What changes with the make is the part: some igniters, boards and motors are specific to a model, and those are ordered. If a part has to be ordered, you get the price and the lead time in writing before you approve anything.

Do you repair heat pumps and electric furnaces?

Yes. On an electric furnace the usual faults are a burned heating element, a sequencer or relay that no longer brings the elements on, a tripped limit switch, and a blower motor or its capacitor. On a heat pump the common faults are an outdoor unit that will not start, a system that runs but does not heat, a unit stuck in defrost, and a failed capacitor or contactor. The visit starts with the same $100 diagnostic, credited toward the repair, and ends with a written estimate. We repair heat pumps and electric furnaces, and we do not install new systems.

Why is my furnace leaking water?

A high-efficiency furnace makes water as it runs. It pulls so much heat out of the exhaust that the vapor condenses, and that water is supposed to leave through a drain line and sometimes a small pump. When the drain line or the trap clogs, the pump fails or a hose cracks, the water ends up on the floor, and many furnaces then shut down on a pressure switch fault. A standard-efficiency furnace should not make water at all, so a puddle under one usually comes from the air conditioner coil above it or from a humidifier. Turn the furnace off if water is reaching the wiring or the control board, and book the diagnostic. We find where the water starts before we replace anything.

Why does my furnace keep turning on and off?

A furnace that runs for a minute or two, stops and starts again is short cycling. The common causes are a clogged filter that makes it overheat, a flame sensor that loses the flame, a thermostat in a bad spot or with a wiring fault, and blocked supply or return vents. Short cycling wears the igniter and the blower and raises the gas bill, so it is worth fixing early. Change the filter and open the vents first. If the cycling continues, we test the limit switch, the flame signal and the thermostat circuit during the diagnostic.

How fast can you fix my furnace?

We can usually schedule the diagnostic for today or tomorrow: you choose the day and a 2-hour window on the booking calendar, any day from 8 AM to 6 PM. We know how long the repair takes only after the diagnostic. If the part is on hand, we fix the furnace on the same visit once you approve the estimate. When a part has to be ordered, you get the lead time with the estimate, and the return visit costs nothing extra.

Is my furnace worth repairing?

Usually, if it is under about 15 years old and the fault is a part: an igniter, a flame sensor, a pressure switch, a blower or inducer motor, a gas valve or a control board. Furnaces often run 15 to 20 years. The case for replacement is a cracked heat exchanger, which is a safety problem and not a repair, or an old furnace that needs one expensive part after another. We tell you which case you are in after the diagnostic, before any work. We do not sell or install furnaces, so if replacement is the right call you take that to an installer, and the $100 is all you have paid us.

What should I do if I smell gas or my carbon monoxide alarm sounds?

Leave the house first. Do not use light switches, the thermostat or a phone inside, and do not try to relight a pilot. From outside, call PG&E at 1-800-743-5000 or 911, and they check for a leak and shut the gas off if needed. If a carbon monoxide alarm sounds, get everyone outside and call 911. Once PG&E or the fire department has cleared the house, we diagnose the furnace side: the gas valve, the burners, the pilot assembly and the venting at the unit.

Do you install or replace furnaces?

No. We repair furnaces and maintain them. We do not install new furnaces, replace whole units or convert a system from gas to electric. If the diagnostic shows the furnace is not worth repairing, we say so in writing and you take that to an installer. Duct cleaning is also not something we do: our work is the furnace itself, its controls and the thermostat circuit.

Do you offer furnace maintenance?

Yes. A furnace maintenance visit is a check of the parts that fail in the cold months: ignition, the flame sensor, the safety switches, the blower, the gas connection at the furnace and the thermostat. The best time is early fall, before the first cold week. There is no published price for the visit: the technician looks at the furnace and writes an estimate, and the $100 diagnostic is credited toward the work you approve. The furnace maintenance page has the full list of checks.

Is there a warranty on furnace repairs?

Yes. Every furnace repair carries our 180-day warranty on parts and labor. If the same fault returns inside that window, we come back at no additional charge.

What payment methods do you accept?

We accept all major credit and debit cards (Visa, Mastercard, American Express, Discover), Apple Pay, Venmo, Zelle, online payment via secure invoice link, personal checks, and cash. You pay after the work is complete and you have approved it. We credit the $100 diagnostic visit fee toward the work if you proceed. If the repair needs a part ordered, we may ask for a deposit on that part before we order it. No processing fees, no hidden charges: the price you approve is the price you pay.

Company Facts · Site Map · Privacy Policy